AIRTRONICS RD 6000 MANUAL PDF
Again, we appreciate your selection of an Airtronics Radio Control System and wish you many hours of flying enjoyment. RD Transmitter Specifications. AIRTRONICS. RD Radio System. Operating Manual. INTIMES no! Airplane Thank you for selecting the Airtronic RD Radio System. In deigning the. download airtronics rd manual. I need a owners manual for an Airtronics RD radio (not the super).. I found one here, but it’s $
|Published (Last):||16 February 2006|
|PDF File Size:||18.79 Mb|
|ePub File Size:||3.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
For initial test flights of your model it is recommended that it be set at a value of 7 to allow for airfronics ability to trim your model.
CPY Copy Copy one model to another. We are showing an example for the Elevator channel. Airtronicw will keep the centering of the servos correct. Crow Left Aileron CR: Aortronics 1 and 3 screws adjust the tension for the vertical motion of each stick.
The screen will change to the following screen to inform you that the process has been completed, and that Model 1 and Model 3 now have the same data, in this example Model 1.
Sanwa RD6000 manual PDF
Changes the linear movement of the servo to the relation of the stick movement. Press this key to select a channel and move to the Right Press this key to move up in a menu Press this key to increase a value or to indicate YES Press this key to decrease a value or to indicate NO Press this key to return to the previous screen Press this key to select a channel and move to the left Press this key to move down in the menu Select Flight Mode Helicopter Note: The 2 and 4 screws adjust the tension for the horizontal motion of each stick.
This is a valuable option as most sailplanes will need a change in pitch trim when ever flaps are deployed.
The RST function will only affect the specific model that you have selected. Remove both switches by sliding them down into the transmitter case and switch locations.
The three servos are mixed in various ways to obtain the control response that is needed for Aileron, Elevator and Pitch control. The servos are mounted on the side frames directly under the Swash Plate with a direct linkage connection from the servo arm to the Airtrojics Plate.
This will be your Slave channel. If incorrect, damage to the transmitter will occur! Exponential is most useful where strong control response is desired at extreme stick positions aittronics softer response to small stick movement is desired in order to make very accurate small corrections to flight path.
Both transmitters must be programmed identically for the trainer system to function properly. Fine tuning of your gyro sensitivity for the various flight modes can be accomplished by flight tests. I will not fly my model higher than approximately feet within 3 miles of an airport without notifying the airport operator. The range of values and default settings for each is shown below. Flight Modes are used to allow activation of the DTM function.
Add to watch list. This feature can also be used on an engine powered model to make small elevator trim corrections as power is applied or reduced. With these servos, mechanical adjustment is the only method available to ensure proper operation of the retracts.
AIRTRONICS RD6000 SUPER User Manual
Skip to main content. After your first flight and your aircraft has been trimmed, you can then program a more precise adjustment for trim authority by use of the STEP function. LA Crow left aileron screen. The airborne components consist of the receiver, which receives the signals from the transmitter, decodes them, and relays the commands to the servos; the servos which are simply electronically controlled motors used to move the controls of the plane; the NiCd battery pack which provides power for the receiver and servos to operate; and the switch harness which allows you to turn the airborne package on and off.
Press the Flight Mode switch to select the different Flight Modes.
airtgonics When you do so, note that the Screen will appear as follows. If by incressing the number moves the elevator in the wrong direction, you can decress the number into the negative side to change the direction of the compensation. The pitch curve for each flight mode has five points that can be adjusted to suit your specific needs. The default settings for RV.
Since you must have two servos to obtain electronic differential, the first thing to do is activate FLAPE Flaperons as indicated on page A common mix would be Aileron to Rudder to achieve coordinated turns without moving the rudder stick. The purpose of this mixer is to allow onw transmitter control input to affect flight functions. If you deside you later that you want to use a feature you have turned off, you can at anytime use the OPT to turn the feature back on.
Estimated on or before Wed. Two servos and two channels receiver channels 1 and 4 are required for V-Tail operation. An extremely versatile feature of the RD Super transmitter is the capability to select 4 different types of modulation.
The trainer transmitter is held by the learning pilot, and does not need to be on the same frequency as the model. After hooking up your controls and mechanically centering all linkages to the approximate positions, press the FUNCTION down key to arrive at the following screen for the Elevator control. Above items will also work with Airtronics Quasar, Radiant, and Vanguard transmitter batteries.
For Sale – Airtronics RD Super, 2 receivers – RC Groups
It has the features available to get the most out of zirtronics type of model. If the differential you set is in the wrong direction, i. This manual has been written to offer the user complete instructions for either fixed wing aircraft or helicopter models. Place the throttle stick in the extreme low position.