DMOR Datasheet PDF, DMOR datasheet, DMOR pdf, DMOR pinout, DMOR data, circuit, ic, manual, substitute, parts. Description. The FSDMRE, FSDMRE and FSDMRE are an integrated Pulse Width Modulator (PWM) and. SenseFET specifically designed for. Features. • Optimized for Quasi-Resonant Converter (QRC). • Advanced Burst- Mode Operation for under 1W Standby. Power Consumption. • Pulse-by-Pulse.

Author: Shakajar Mooguzragore
Country: Croatia
Language: English (Spanish)
Genre: Video
Published (Last): 2 December 2016
Pages: 457
PDF File Size: 15.43 Mb
ePub File Size: 4.84 Mb
ISBN: 477-5-44592-670-1
Downloads: 88771
Price: Free* [*Free Regsitration Required]
Uploader: Dumuro

SN datasheet – Texas Instruments Documents. These parameters indicate the inductor current. In this generation the startup resistor is replaced by an internal high voltage current source. Free standing with no heat-sink under natural convection.

It is designed to drive the transformer directly. An opto-coupler such as the H11AA and shunt regulator such as the KA are typically used to implement the feedback network.

TempShutDown Delay Current vs. Ql5 datasheet pdf QL5 datasheet, Pulse width limited by maximum junction temperature 2.

DMO565R даташиты PDF

These parameters, although guaranteed, are tested in EDS wafer test process. If Vfb exceeds 2. In order to prevent this situation, an over voltage protection OVP circuit is employed. Published on Apr View This device is a basic platform well suited for cost effective designs of flyback converters.

TempBurst Mode Enable Voltage vs. Comparing the feedback voltage with the voltage across the Rsense resistor plus an offset voltage makes it possible to control the switching duty cycle.

DMOR Datasheet PDF – Fairchild Semiconductor

Typical continuous power in a non-ventilated enclosed adapter measured at 50C ambient. SN datasheet – doctor- SN datasheet Author: When Vcc reaches the UVLO stop voltage, 8V, the protection is reset and the internal high voltage current source charges the Vcc capacitor via the Vstr pin. In this situation, the protection circuit should be activated in order to protect the SMPS. In this manner, the auto-restart can alternately enable and disable the switching of dmo55r power Sense FET until the fault condition is eliminated see Figure 6.


When the temperature exceeds approximately C, the thermal shutdown is activated.

DMO565R View Datasheet(PDF) – Fairchild Semiconductor

Assuming that the 0. Texas Rmo565r – Subject: Because more energy than required is provided to the output, the output voltage may exceed the rated voltage before the over load protection is activated, resulting in the breakdown of the devices in the secondary side. The voltage on the output capacitors is progressively increased with the intention of smoothly establishing the required output voltage.

Once Vcc reaches 12V, the internal current source is disabled.


If the voltage of this pin reaches 6. The PWM controller includes integrated fixed frequency oscillator, under voltage lockout, leading edge blanking LEBoptimized gate driver, internal soft start, temperature compensated precise current sources for a loop compensation and self protection circuitry. Cdbe datasheet pdf – datasheet pdf Cdbe datasheet pdf The collector of an opto-coupler is typically tied to this pin.

Then, Vfb climbs up in a similar manner to the over load situation, forcing the preset maximum current to be supplied to the SMPS until the over load protection is activated. Excessive voltage across the Rsense resistor would lead to incorrect feedback operation in the current mode PWM control. This reduces the current through the opto-coupler LED, which also reduces the opto-coupler transistor current, thus increasing the feedback voltage Vfb.


This pin is the positive supply voltage input. However, even when the SMPS is in the normal operation, the over load protection circuit can be activated during the load transition. If the secondary side feedback circuit were to malfunction or a solder defect caused an open in the feedback path, the current through the opto-coupler transistor becomes almost zero.

Qlt datasheet pdf – datasheet pdf Dayasheet datasheet, In this condition, Vfb continues increasing until it reaches 6V, when the switching operation is terminated as shown in Figure catasheet. These parameters, although guaranteed at the design, are not tested in mass production. Overload is defined as the load current exceeding a pre-set level due to an unexpected event.

In order to avoid undesired activation of OVP during normal operation, Vcc should be designed to be below 19V. This causes the feedback voltage to rise.

Rockchip RK datasheet V0. When Vcc reaches 12V, the internal high voltage daatsheet source is disabled and the power is supplied from the auxiliary transformer winding.