FRENIC LIFT MANUAL PDF

FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Mazulkree Voodoorg
Country: Anguilla
Language: English (Spanish)
Genre: Health and Food
Published (Last): 14 August 2008
Pages: 166
PDF File Size: 6.15 Mb
ePub File Size: 14.13 Mb
ISBN: 259-8-70093-290-1
Downloads: 84031
Price: Free* [*Free Regsitration Required]
Uploader: Yozshuramar

Page 31 These are provided for the DC link bus powered system. Disable Times Times 1 to It is recommended that the following parts be replaced as specified below.

Do not hold covers or individual parts only. Tuning procedure What follows gives you a tuning procedure of the inverter for a motor using mnaual multi-function keypad option. Marks to classify these situations in the torque control column of the function code table on the following pages as shown below.

Fuji Electric FRENIC-Lift series Instruction Manual

When the replacement is necessary, contact your Fuji Electric representative. Precautions for use Driving a V When driving a V general-purpose motor with an inverter using ex- general-purpose tremely long wires, damage to the insulation of the motor may occur. FRENIC-Lift is an inverter manuwl to drive a three-phase induction motor hereafter called an induction motor and a three-phase permanent magnet synchronous frenicc hereafter called a synchronous motor for exclusively controlling elevating machinery.

External View And Terminal Blocks 1. Page 85 Table 7.

By pressing ‘print’ button you will print only current page. For the motor, check the rated values printed on the nameplate of the motor. Driving gener- When high starting torque is required or quick acceleration or deceleration al-purpose motor Selecting is required, select an inverter with a capacity one size greater than the inverter standard.

  CONAN IL RAGAZZO DEL FUTURO ROMANZO PDF

Insulation Test A dielectric strength test will cause breakage of the inverter similarly to the Megger test if the test procedure is wrong. Page 55 E codes: Terminal Arrangement And Screw Specifications 2.

The two terminals prepared for grounding, which are indicated by the symbol G in Figures A to C, make no distinction between the power supply side primary circuit and the motor side secondary circuit. Page 40 Table 2. lifg

FRENIC-Lift | Fuji Electric Global

Measure the output current. To print the manual completely, please, download it. Page of Go. Also remove the case fixing screws from the top. Check that a mechanical brake is in effect. If any of the problems listed below occur, take an appropriate measure against them. Mounting the covers Put the front cover to the inverter case so that its bottom engages with the hinges provided on both sides of the case. Page 54 F codes: Possible Causes What to Check and Suggested Measures 1 Conditions for Compare the settings of the y codes y01 to y10 with those of the host communications differ equipment.

Push the front cover against the case of the inverter and slide it upward until the latch at its top engages with the case. These lifft provided for the DC link bus powered system.

  6ES7 307-1EA01-0AA0 PDF

Page In no event will Fuji Manaul Co. An undervoltage or an alarm has been occurred.

Using this adapter greatly A dielectric strength test will cause breakage of the inverter similarly to the Megger test if the test procedure is wrong. Removing the cable guide plate Before to proceed, remove the terminal block cover as shown below left.

In no event will Fuji Electric Co. Page 30 Grounding terminals G Be sure to ground either of the two manuak terminals for safety and noise reduction. To frsnic cooling efficiently, you can take the heat sink out of the equipment or the enclosure as shown on the right so that cooling is done both internally and externally this is called mankal cooling”.

Enter text from picture: Chapter 4 Running The Motor U, V and W respectively and that the grounding wires are connected to the ground electrodes correctly.

Torque limit time 0.

The first letter is an alphabet that identifies its group and the following two letters are numerals that identify each individual code in the group. Lower the temperature around the motor. Store them for future use. Page 48 Tuning procedure What follows gives you a tuning procedure of livt inverter for a motor using a multi-function keypad option. The standard motor and the inverter motor are protected in the range of all the frequencies.